How To Use Husky HVLP Spray Gun

HVLP spray guns have been used for many years in the film industry. The machine is easy to control and needs less air, which saves energy.

Conversely, the paint has a wider range of spray. By reducing the air pressure, the coating can be made more precise, and it is ideal for coating the surface of objects.

use husky spray gun

The HVLP spray gun performs a key role in airless painting. You can take advantage of the mechanical properties of the spray gun in conjunction with the excellent properties of the HVLP.

A Husky HVLP spray gun is one of the best systems for spraying paint. The Husky HVLP gun has a large fan size for reduced overspray.

The paint is sprayed through a thin hose using compressed air in order to reduce the size of the droplets that are formed.

This makes for a much smoother finish and for reduced drying times. The Husky HVLP gun is easy to use and the instructions found below should help you get started with your paint project.


How To Use Husky HVLP Spray Gun

What is a Husky HVLP Spray gun?

The Husky HVLP spray gun system is really an efficient tool and it doesn’t waste material. A skilled operator can work at a very good speed saving time, money, and resources.

It also offers more control when spraying which can be beneficial in various circumstances in terms of spray coverage and material flow.

The paint comes out evenly on the surface without any over-spray which is terrific since it provides a beautiful finish that is both accurate and consistent in exactly the right amounts.

(It’s so much better than spray guns that shoot high overspray.

Husky spray guns are equipped with easy-to-use regulators that control and adjust the machine.

Tanks and cups come in different varieties and capacities, made of plastic and aluminum with copper air cap rings, stainless nozzles, and needles.

Method to set up Husky HVLP gun

First, you have to open the gun and adjust all the parts. Then adjust the air compressor to 90psi so that compressed air delivers to the spray gun.

Pull the trigger in order to spray on the surface and set the air regulator at 40 psi (according to the surface). To make the air volume stable fix the air inlet valve which is at end of the handle.

Adjust the knob in order to pull it clockwise. With the help of a knob, you can set the output.

If you turn it anticlockwise then it will spray more paint and if you turn it to a clockwise position then it will give a shorter stroke of paint.

Mix paint with water. Use a fine filter or cloth to run the paint mixture in order to check if any blockage happens then we can fix it. Fill the tank to ¾ to its maximum level.

Method to use Husky HVLP spray gun

Put a mixture of paint in the reservoir and fill it properly. Turn on the air compressor in order to spray paint from the husky HVLP spray gun.

Check the paint on some cardboard surfaces before spraying on the project so we can fix the paint mixture if it spits or unevenness occurs.

Don’t overspray the surface spray thin coats of paint. More thin coats are better than fixing the overcoating problem.

Operating the gun

Air-powered spray guns are designed to perform a variety of spraying applications in places where you do not want to use a combustion engine-powered spray gun.

They utilize the pressure from a compressor so that the atomized material gets sprayed more specifically.

And with more control, since there is no engine slowing down its speed of working, or even asking for specific changes when situations get more complicated.

This particular air-powered paint sprayer features an HVLP (high volume low pressure), which enables it to work efficiently and at optimal capacity.

This means that you also save money material-wise with this technique.

using husky HVLP spray gun

Don’t exceed 40 Psi! First, connect to the air source and pump that bad boy up until it starts making some nice phssssht-ish sounds — you’ll know what we mean.

Then, call upon your paint of choice and load that baby in the gun by pressing down on your lever thingie with a death grip on your spray can.

Be careful not to shake too much or get any water in there – this isn’t a science experiment!

When you’re all loaded up and good to go, hold that trigger lever down as tight as you can with both hands pointed away from anything valuable.

Control the pattern and fluid flow

Before using the sprayer to paint, let’s adjust the settings! First, test that the airless sprayer is properly connected to a source of clean water by turning on the water.

The wand must be under running water for at least three seconds without leaks before proceeding with the rest of this checkup.

It’s important to remember: All hoses and nozzles must remain under pressure while you’re testing them or they will not spray correctly.

To control the flow of spray, turn the dial to turn on and adjust the pressure to control how much is coming out of your nozzle.

To land a stream on its target, you need to move the nozzle up and down until you find just the right balance by flicking back and forth.

Preparing the paint

In order to spray paint, start by thoroughly mixing the paint and thinning it with a suitable solvent.

Some paints require more thinning than others and you can find specific instructions for your specific needs on the paint manufacturer’s label. Most materials will spray readily if thinned properly.

Strain the solvent through cardboard or other material (cheesecloth or a paint strainer are better options but may not be easiest for all situations).

And then add to a clean selected container (preferably one with a spout!).

Fill up approximately 3/4 full of your container with your mixed material leaving room for thinner if necessary – solvent containers tend to overfill at times so this is to avoid this possibility.

Paint with the sprayer

Begin spraying. Always keep the spray gun at a right angle to the work surface.

Keep the nozzle about 6 to 9 inches from the work surface throughout the stroke and always keep the gun in motion while spraying.

Stopping gun movement in mid-stroke will cause a buildup of paint and result in runs. Do not fan the gun from side to side while painting.

This will cause a build-up of paint in the center of the stroke and an insufficient coating at each end.

Trigger the gun properly. Start the gun moving at the beginning of the stroke before squeezing the trigger.

Release the trigger before stopping the gun movement at the end of the stroke. This procedure will feather (blend) each stroke with the next without showing overlap or unevenness.

To use the sprayer, open up the compressed air source. Point the air nozzle at your workpiece and in a gentle sweeping motion apply pressure to the trigger while moving away from your piece.

Use an old cardboard box to catch overspray when you paint over the edges of your workpiece. If you need to paint part of your workpiece, cover it with masking tape to prevent overspilling.

How do you use a HVLP spray gun?

HVLP (High Volume Low Pressure) spray guns are a type of paint spray gun that is designed to use high volumes of air to atomize and spray paint while using low air pressure.

This results in a more efficient and higher quality application of paint, with less overspray and waste. To use an HVLP spray gun, follow these steps:

  • Fill the paint cup with the desired amount of paint, following the manufacturer’s recommendations for the specific type of paint being used.
  • Adjust the pressure on the compressor to the recommended PSI for the HVLP spray gun. This will usually be between 10-45 PSI.
  • Connect the air hose to the compressor and the HVLP spray gun.
  • Test the spray pattern on a piece of cardboard or other scrap material, adjusting the fluid and air pressure as needed to achieve the desired pattern.
  • Hold the spray gun 6-12 inches from the surface to be painted, and begin spraying in a side-to-side motion, overlapping each pass slightly.
  • Use steady, even strokes to apply the paint, moving the spray gun at a consistent speed to avoid drips and splatters.
  • When finished, turn off the compressor and release any remaining pressure in the spray gun before cleaning it according to the manufacturer’s instructions.

How do you adjust a husky spray gun?

Husky is a brand of paint spray guns that are known for their durability and versatility. To adjust a Husky spray gun, follow these steps:

  • Begin by adjusting the fluid nozzle to the desired size. The fluid nozzle controls the amount of paint that is sprayed and can usually be adjusted by turning it clockwise to increase the size of the opening, or counterclockwise to decrease it.
  • Next, adjust the air cap to control the shape and size of the spray pattern. The air cap can usually be adjusted by turning it clockwise to increase the size of the pattern, or counterclockwise to decrease it.
  • If the spray gun has a pressure adjustment knob, use this to control the pressure at which the paint is sprayed. Turning the knob clockwise will increase the pressure while turning it counterclockwise will decrease it.
  • If the spray gun has a fan pattern adjustment knob, use this to control the shape of the spray pattern. Turning the knob clockwise will widen the pattern while turning it counterclockwise will narrow it.
  • Test the spray pattern on a piece of cardboard or other scrap material, adjusting the fluid nozzle, air cap, pressure, and fan pattern as needed to achieve the desired results.
  • When finished, be sure to clean the spray gun according to the manufacturer’s instructions before storing it.

Do you have to thin paint for a HVLP sprayer?

In general, it is recommended to thin paint before spraying it with an HVLP (High Volume Low Pressure) sprayer.

This is because HVLP sprayers are designed to atomize and spray paint using high volumes of air at low pressure, and thicker paints may not atomize properly when sprayed through the gun.

Thinning the paint helps to improve the atomization process, resulting in a smoother and more even application of the paint.

To thin paint for an HVLP sprayer, you can use a paint thinner or reducer specifically designed for the type of paint you are using.

Follow the manufacturer’s recommendations for the proper amount of thinner to use, as adding too much thinner can negatively affect the performance of the paint.

You can also use water to thin water-based paints, although this is not recommended for oil-based paints.

It is important to note that some paints may not require thinning at all, and can be sprayed through an HVLP sprayer without any additional thinning.

In general, it is best to test the paint on a scrap piece of material before spraying it on the final project, to ensure that it is atomizing properly and providing the desired results.


FAQ’s of How To Use Husky HVLP Spray Gun

There are many guns on the market and a variety of settings to use. Many people are confused about how much pressure to use. The key is to begin low (4 oz.) and increase until you’re comfortable. You don’t want to start too strong. Too much pressure can damage the gun and/or the job. I like to use 10 to 12 oz. of pressure for most jobs. The best way to find the correct pressure is to test the gun with water. Open the gun and blast water out of the spray gun. If the edges of the fan are rounded, then you’re using too much pressure. If the water is blowing out in a straight stream, then you’re using too little pressure. When you find the right pressure, you will see a nice, smooth fan.

It’s very simple! When you get a smooth finish, it’s because the paint has a lot of tiny bubbles. To get a smooth finish with an HVLP sprayer, you should use long, light and even strokes. You should spray perpendicular to the surface of the object you are painting, and with the right distance. You should also make sure that your gun is clean and the paint is thinned enough. One more thing to note is that the paint should be slightly warm to the touch, but not hot. Just like you should avoid thick layers of paint, you should avoid thick layers of HVLP sprayer. If you have to paint a big surface, you should do it in at least 3-4 light layers.

A big air compressor will ensure that you are able to paint for long without stopping. When choosing a big air compressor, make sure that it has a motor of 3.2hp or greater. Get one that’s at least 6 cfm.

First time you fire up the spray gun, let it burn off the overspray and any dust or other contaminants that may be in it. Also, you should always spray a test pattern, in order to see the pattern, you will get when painting. You should always run the gun with solvent, not just air, if you are using solvent based paint. The gun will spray differently with each type of paint, so to be accurate you need to spray the actual paint you are using.


Conclusion of How To Use Husky HVLP Spray Gun

If you are a beginner painter and want to purchase a new HVLP spray gun then you must read this article.

It will give you an idea about how to use a husky HVLP spray gun for your projects and what things you should consider when you are buying a new HVLP spray gun.

This guide is best for those newbies who want to achieve the desired results out of their work. Thus, this guide will help you to achieve those results.

Feel free to ask anything regarding this post in the comments section.

Matthew Edward

Matthew Edward is a professional painter who loves to paint and wants to share useful tips and tricks which he had learned in many years of experience in painting. He also used many products that can be used for painting he has tried and tested each and every product to give an unbias opinion about it in his review. This blog is very useful for those newbies who want to learn painting without making mistakes.

Leave a Comment